1. Focus on print. Start every first ink-jet printer, the printer must print head cleaning and initialization printers, ink delivery system for filling ink, it is obvious that cause waste of ink. In addition, the use of the CANON printers, a printer by holding down the “resume” button (reset) more than 2 seconds, the printer will print head cleaning. Therefore, if there is lack of printer paper, installed according to post-paper “resume” button faster, not more than 2 seconds.
2. The use of economic models. The new ink-jet printer, taking into account the people’s pockets have increased “economic model of print” function, the model can be used to save almost half of the ink, and significantly improve the printing speed. Canon and as early as a few years ago on the “super-economic model,” provincial Mexican ability to make even more outstanding. Some models in the model, can save 75% of the ink. However, it is worth mentioning that the use of the print quality mode, but it falls short, so the recommendation in the sample print or print only when a draft choice of economic models.
3. Printhead cleaning. Most of the ink-jet printers will start self-cleaning print head, and there are buttons on the print head for cleaning, such as the vast majority of Canon inkjet printer with the rapid cleaning, washing and thorough cleansing routine cleaning function of third gear.
4. Clever use of page layout for printing. The ink-jet printer page layout to support all the way to print documents and use the approach to printing, a few will be able to concentrate on the content of information to the printed page. In sample print when this function and to combine economic model will be able to save a lot of ink. However, the function not only to Mexico in order to save the settings. For example, you want to print a book’s cover, also found that the function is very useful.
5. Print their own definition of the way. Economic model based on the quality of printing to reduce the cost to save ink, and print While the standard model to the evaluation results are costly. Is it really can not have both fish and bear’s paw? In fact, most of the ink-jet printer models so that we can choose a different concentration of print, and adjust the concentration of print, so as to achieve the purpose of saving ink. In addition, the cartridges can be used, the type of media to adjust a variety of options, the definition of its own printing mode. However, a group set up for different cartridges and paper, the results will certainly be different, you can print in fine-tuning to do before, in order to achieve the best condition. Satisfied with the test, you can click the Save button, type the title, such as “common”, also described in the column on the input from the current definition of a simple print mode settings description.
6. Not to immediately replace the cartridges. We know that the ink-jet printers through the induction sensors to detect the amount of ink in the cartridges, as long as the sensor detects the amount is less than one ink color printer within the set value, they are prompted to replace the cartridges. At this time, the cartridges can be immediately put out, and then through the control panel button cleaning, the printer can also bring their own software tools to clean, repeated several times, most printers can use normal. Remove the printer cartridges so that the reduction of internal sensors to determine the installation of a new cartridge, but must pay attention to is this: Do not be carried out under a state shutdown. In the cartridges have not run out of time, it is best not to be removed in order to avoid an unnecessary waste.
Second, to deceive your printer
Of course, no matter how the province can not ensure a lifetime cartridges. There are always warning the printer, there are extraordinary measures can help you save money:
The first one: to deceive the printer. In fact, the above article is the sixth in the deception. In addition, the EPSON, ink cartridges in the direction through the cartridge into the printer when setting the type of paper and printing had to calculate the number of sheets of the judge, about 100 or so print it that the ink has run out, in fact, at this time cartridges Maybe a lot of ink in the left. Once I had a friend in the machine to do a test, in the second run out of ink cartridges loaded in the third month before the original down for the first cartridges loaded, and the results of the normal print 30 pages or so, and then began to fade on the , The cartridges must be replaced at this time, but there are procedures that the ink cartridges (of course it counts to 30), and this time it is necessary to force the replacement cartridges.
At this point, but can not use the normal replacement of the cartridges because the procedure that will not run out of ink cartridges can not be automatically moved to the replacement of aircraft location of the cartridges, which must be in the frame cartridges at the beginning when the slow-moving from right to left to force the closure of power, With the closure of the outlet or power plugs out of the way (out of order, do not forget to customs the power button on the printer so that the cartridges to the frame), then carefully slow cartridge frame to move to open a replacement printer cartridges position after the far left , After the ink cartridges to replace aircraft began to move to the location (if it is the same as the normal replacement ink cartridges that it will remain in the far left, the program will go wrong, and may damage aircraft mobile cartridges and the corresponding motor pulley!), And then the implementation as long as you Print nozzle cleaning process can be used to normal.
Remember! Because of the new cartridges from the first X Zhang (replacement printer cartridges former record of the number of sheets), the corresponding Zhang hit a few times that the program will be exhausted ink cartridges, at this time, as long as the replacement cartridges in accordance with the normal operation Ink cartridges will be from the plane back out again (do not even have to come up with cartridges, ink cartridges on the shelves as long as the re-release the clamp on the card can be a bear), the procedures used ink-check inspection tool, Hey! Cartridges are Full.
The second measure: perfusion method to deceive. Deceive or re-stem and Mexico have, you think I would like to filling the ink? Wrong, not the last, the printer will not compromise. Remove the cartridge and then sealing the Mexican population. A medical syringe, take 3-5 ml distilled water. Zhu Mo from the hole into the cartridge (not too much), and then forced Shuaidong cartridges to allow water to sink to a Mexican port. Repeat this process a water injection, cartridges, so there are 10 milliliters of ink. The emergency should be able to print. Shuaidong cartridges can be many times. Let cartridges in the water, up and down repeatedly. Because each repeat, distilled water can dissolve more of the original ink. If the print quality do not ask for much, you almost can not tell, which is distilled water or irrigation of the new alternative ink.
Using this method you can play more than 100 pages. In fact, is to make full use of the cartridge in which the large sponge. It should be noted that, we use distilled water, impurities in the water too common, greedy should not bear in mind that if too much distilled water injection has not worked. In addition, you also look at the original quality of the ink, printing results will be close to the original ink. It should be noted that in particular, to distinguish what is a Mexican population, what is Zhumo mouth. Because there is a Mexican near a metal filters. Since then, if the damage it would be refilled, the impact caused by filtering plug. Of course this is only emergency measures.
“Evil schemes” on these basic, with regard to alternative ink and ink from the print quality, the ink will play better. More on this area. Shanghai producing useful Heroes of the High carbon ink licensing (very easy to plug), ink Chunlan licensing of the West Lake in Zhejiang Province (non-formal and easy to fade) and the Pearl of ink (light colors), After a series of attempts to plug, in particular the recommendation to the poor and their buddies Needle pen and ink water (with art), because the art work by the pen nib fine needle only 0.3mm, very few impurities, after the color printing is also very dark, very good results. However, the phrase is an old, with no alternative ink by the original, the Federation of plug more chance, please think twice.
Third, the Mexican province of the G-8 proposal
In addition, both compatible with ink or the alternative, there are a few recommendations to keep in mind:
1. Was to ensure that the filling of cartridges is intact;
2. To make full use of high-quality original ink to fill;
3. Filling in again before the ink should be thoroughly cleansed of the original cartridges clean, otherwise occur two different mix of ink and chemical reactions caused by failures such as the plug. Do not bring their own printer cartridges cleaning procedures for cleaning, this operation is not only time-consuming and may not have enough clean clean. The correct method of operation are: Canada and Mexico, used a syringe to inject pure water cartridges, so as not to allow water to overflow, and then seize the hands of the whole cartridges, ink and add up hole, gently shake a few, so that The residual ink fully dissolved in water added.
If this was excessive force when they shake may be inside the liquid spill, this time in a timely manner with dry cloth or paper towel to prevent the infiltration of the spread of the circuit board cause hardware failure, and then re-use syringes cartridges will be pumping liquid mixture of clean , So the operation repeated several times until the liquid out to see the color of light used to bring their own printer cartridges cleaning procedures for cleaning;
4. To the filling ink cartridges, must be appropriate;
5. Ink ink as far as possible choices to fill;
6. Filling in for good ink cartridges, ink cartridges would be best to allow a few minutes before standing, so that ink sponge slowly penetrated into every corner of the mat in order to ensure that the final print quality;
7. Cartridges to avoid long exposure to the air and have a dry plug, despite its clean, but should be finished soon ink cartridges refilled immediately after, and refilled immediately after the printing machine. If the printer does not use for the time being, will also be head nozzle on a dedicated storage box, a special rubber mats can be separated by air, keep the nozzle for a long time wetting;
8. If the print cartridges and the nozzle is integrated together, then add to the ink cartridges, the cartridges must pay attention to the protection of the nozzle from harm, otherwise, if it is to plug nozzles or damage, the cartridges can not be used again . In addition, due to the frequent use of cartridges in the process, the head may be back to the splash of paper fiber plug, which led to the deterioration effect of the output nozzle, spray on a regular basis to carry out the washing is also very necessary. Nozzle cleaning, to make full use of wet paper towel and gently clean cotton towel nozzle on the edge, rather than run the nozzle, and then, re-use ink-jet printer control panel on cleaning key to the implementation of the nozzle cleaning action until the printout Clear results so far.